× This listing has expired.

Compressed Natural Gas (CNG) Station Equipment

Current Auction - Package includes Storage, Compressor, Dispensers

 
Listing Image
Send a message or question to the listing poster:*
Date Expires
Date Posted
Posted By   admin
View More Listings
Description

ONLINE AUCTION: Ends January 29th at 2 PM EST

EQUIPMENT LOCATION: Miami, FL

TOTAL ORIGINAL COST:  $470,000

MINIMUM BID:  $20,001* NOTE: Please read auction terms. Buyer Internet Premium of 15% to be paid by winning bidder.

Place Bid, Review Auction Bidding Requirements, and See Aditional Pictures HERE

 

Equipment Package Includes:

 

STORAGE

Manufacturer: ASPRO

Year: 2012

Original Cost: $70,000

Storage Package Includes: 3 modules containing 30 cylinders total, with interconnecting tubing, valves and safety devices

Current Location: Miami, Florida

Condition Notes: Per seller, machine working well and equipment does not need anything or has not been recently repaired.

Technical Specifications:

  • Start / Stop Pressure sensor for fully automated compressor control.
  • Priority valve in one line.
  • 4” Pressure gauge.
  • Inlet and Output handle ball-valve.
  • Inlet check valve.
  • Output actuator valve for automatic shut off.
  • Safety valve.
  • Excess flow valve in each output line.
  • Maximum working pressure: 4500 psig.
  • Hydrostatically tested at 6525 psig.
  • Manual valve in each cylinder to close it independently with burst disc included.
  • Frame with steps for easy access to each cylinder valve.
  • Full stainless steel pipes and fittings.
  • DOT Cylinders.

 

UNIT COMPRESSOR PACKAGE

Manufacturer: ASPRO

Model: IODM 115-5-4R

Original Cost: $270,000

Compressor Package Includes: 1 Reciprocating compressor, horizontal opposed cylinders, balanced, 5 stages including pre-compression, lubricated.

Year: 2012

Hours: 352

Current Location: Miami, Florida

Condition Notes: Per seller, equipment was working well until switched off due to a corporate decision. Small areas of rust.

Technical Specifications:

  • Single manufacturer for the complete unit: Bare Shaft, Condensers, Safety Valves, Blow Down Tank, Knock Down Tank, etc. all made by ASPRO.
  • Compressor Type: Horizontal Alternative Reciprocating System.
  • Type of Operation: Continuous.
  • Oil lubricated Compressor for long life and minimum maintenance. First preventive maintenance with rings replacement at 10.000 running hours.
  • Crankcase gear oil pump, Pistons cam oil pump, oil filter and oil cooler everything included. 
  • Unpressurized Crankcase.
  • Number of stages:  Five (5).
  • Pre Compressor or Booster working as first stage.
  • Stroke: 115 mm.
  • Inlet Pressure Range: 2.9 to 16 PSI.
  • Output Flow Capacity: 280 SCFM @ 2.9 PSI; 497 SCFM@ 16 PSI.
  • Discharge Pressure: 4500 PSI
  • Electric Motor - Bare Shaft connection through belts coupling for maximum energy efficiency.
  • Compressor speed 1000 RPM.
  • Pre-Compressor speed 900 RPM.
  • Compressor Electrical Motor 185 KW – 480 Volts 60 Hz, SIEMENS, explosion proof NEC classification zone 1, group II.
  • Pre Compressor Electrical Motor 55 KW – 480 Volts 60 Hz, SIEMENS, explosion proof NEC classification zone 1, group II.
  • Air Cooling with Fan refrigeration incorporated to the compressor. Null maintenance compared to other systems like water cooling.
  • Safety system composed of pressure switches, thermostats, shut off valve and inter-stages safety valves.
  • Inter stage condensers and collector tank with automatic drain valve.
  • Last stage coalescent filter with oil filtration < 5ppM.
  • Sensors and alarms for: Discharge high pressure, high or low suction pressure, Discharge high temperature, High vibration level, Low oil pressure, Low oil level, Motors current overload.
  • Power safety system: installation under codes and with inherently safety device.
  • Equipped with a panel containing visualization instruments for Inter stages pressures and Inter stage temperatures with all the safety elements.
  • Simple installation due to the disposition of its connections.
  • Easy installation over six (6) included Vibration Dampers. 
  • Clearance pocket regulator in pre-compressor and main compressor.
  • Fully automated system through SIEMENS Control Panel with last generation PLC and Color Touch Screen.
  • Automatic start up when minimum pressure is reached in the storage and automatic stop when maximum operating pressure is reached.
  • Two (2) Soft Starters included in Control Panel for smooth motors start with low current demands.
  • SCADA System included.
  • Dimensions: Length= 12’ 4”, Width= 6’ 10”, Height= 8’ 6”.
  • Weight: About 17,600 Lbs. according to configuration and accessories.
  • Design Standard: ISO 9001-2000.
  • Design Specification: ASME VIII, div. 1.
  • Equipment based on Standard API-618 and ISO 13631 where applicable.
  • Certificates regarding test and inspections carried out during material procurement and equipment manufacture available according QAP (Quality Assurance Program).
  • Vibration limits according to ISO 10816-6, 1995-12-15, "Mechanical vibration-Evaluation of machine vibration by measurements on non rotating parts", part 6, "Reciprocating machines with power ratings above 100 kw
  • All components are UL listed.
  • Equipment complies with NFPA52 regulations.

 

DISPENSERS

Manufacturer: Bennett / CNGAS Pacific

Quantity: 2 units

Model: C30

Original Cost: $130,000

Serial Numbers: 6R970704 & 6R970705

Year: 2013

Hours: 352

Current Location: Miami, Florida

Condition Notes: Per seller, machine working well and equipment does not need anything or has not been recently repaired.

Technical Specifications:

  • Dual credit card reader built-in.
  • Dual 5.7” color display.
  • Secure payment module.
  • Dual PCI compliant debit/credit reader and receipt printer.
  • Electric power supply: 110Vac +/- 10%; 60Hz.
  • Operation ambient temperature: -4F to + 140F
  • Maximum working pressure: 45000 psig
  • Hydrostatically tested at 6525 psig  
  • Two (2) simultaneously filling hoses.
  • Two (2) mass flow sensors.
  • Two (2) quick disconnect breakaway valves.
  • Manual shut off valve
  • Microprocessor controlled. Fully automated system with habilitation switch included.
  • Leakage flow detection during standby mode.
  • Liquid quartz electronic display for each hose with Unit price, GGE delivered and total amount to be paid in dollars.
  • Pressure regulator valve in each hose for maximum filling pressure set at 3625 psi
  • 4” Pressure gauge, minimum 5800PSI with pressure switch alarm.
  • Vent hose included.
  • One line sequence with Inlet filter.
  • WEH TK17 nozzle.
  • Communication interface protocol for remote control and monitoring.
  • Base plate for fastening to ground included.
  • NTEP weight & measures certified.
  • All components are UL listed.
  • Equipment complies with NFPA52 regulations.
  • Made in USA.